Region:
TECH-MASTERS Group Changing region
  • TECH-MASTERS Austria
  • TECH-MASTERS Germany
  • TECH-MASTERS Croatia
  • TECH-MASTERS Czech
  • TECH-MASTERS Poland
  • TECH-MASTERS Slovakia
  • TECH-MASTERS Hungary
  • TECH-MASTERS Romania
  • TECH-MASTERS Slovenia
  • TECH-MASTERS Italia
  • TECH-MASTERS Group

Seal Flex HT red

Product variant for
General «
General
Automotive

SEAL FLEX HT RED is a modified, uv-resistant sealant, based on acetoxy RTV silicone, that is essentially odorless. This non-corrosive silicone, with excellent adhesive properties, can be used on a wide variety of materials and especially where no discoloration or corrosion of sensitive materials is accepted.
SEAL FLEX HT RED forms a strong, tough, flexible and resilient elastomeric rubber, with excellent chemical and high temperature resistance, that maintains its flexibility at low temperatures and stability at high temperatures.
Apply SEAL FLEX HT without using any extra tools directly from the pressure can.

  • The ideal gasket without molds
  • Workable in few minutes
  • Created for automotive applications
  • It fills the unevenness
  • Non corrosive
  • Immediate results on water or air
  • High chemical resistance; it resists also against engine oil
  • High pressure and UV resistance
  • Temperature range: -60°C to + 300°C
  • Easy to remove
Article nr Name Content
T571701 Seal Flex HT red 200ml 200ml
T571702 Seal Flex HT red 310ml

» To the shop
  • Technical data
  • Application and usage
  • Downloads

Form: pasty
Material: acetoxy RTV silicone
Colour: red
Odour: characteristic
Density (at 20°C): 1,04 g/cm³
Viscosity: non-sag paste
Tack-free time: 10 min
Cure time (at 23°C, 50% r.h.): 4mm/24h
Hardness Shore A: 25
Tensile strength: 1,8 MPa
Shear strength (alu, 1mm): 2,0 MPa
Elastic Modulus (100%): 0,52 MPa

Elongation at break: 500%
Recovery from deformation: 98%
Temperature resistance: -60°C to 300°C
Dielectric strength: 20 kv/mm (ASTM D 419)
Dielectric constant: 3 at 1 Mhz (ASTM D 150)
Dielectric dissipation factor: 3x10-3 at 1 Mhz (ASTM D 150)
Volume resistivity: 2x1015 OHM cm (ASTM D 257)
Thermal conductivity: 315 cal/sec./cm², °C/cm
Shelf life: 24 months in unopened packing below 25°C

  • SEAL FLEX HT RED is developed for many industrial sealing and insulating application, including metal and glass construction, automotive, marine, mechanical engineering, screw thread connections, machine tools, maintenance, connections, air ducts, inlet and outlet manifolds, compressors, pumps, turbines, electrical/electronic, aerospace and consumer products.
  • insulating and moisture-proofing  of engine and electrical boxes
  • sealing of water leakages on rear lights and body joints
  • SEAL FLEX HT RED is jointing to: metals and different alloys, glass, ceramics and several kinds of synthetic materials
  • SEAL FLEX HT RED is resistant to: light acids (up to 20%), glycol, fluor-chlorine-methane, butane, oils, greases, lubricants, petrol, kerosene, transmission and brake fluids, water, steam, antifreeze agents, fuel oil, alkali, saline solutions
  • For an optimal adhesion, the surfaces should be dry and free from corrosion, oil/grease or dust. Therefore we recommend cleaning the surface with a solvent.
  • We recommend to test SEAL FLEX HT on the substrate before use

Seal Flex HT red

Product variant for
 «
General
Automotive

Seal Flex HT red

Product variant for
 «
General
Automotive

SEAL FLEX HT RED is a modified, uv-resistant sealant, based on acetoxy RTV silicone, that is essentially odorless. This non-corrosive silicone, with excellent adhesive properties, can be used on a wide variety of materials and especially where no discoloration or corrosion of sensitive materials is accepted.
SEAL FLEX HT RED forms a strong, tough, flexible and resilient elastomeric rubber, with excellent chemical and high temperature resistance, that maintains its flexibility at low temperatures and stability at high temperatures.
Apply SEAL FLEX HT without using any extra tools directly from the pressure can.

  • The ideal gasket without molds
  • Workable in few minutes
  • Created for automotive applications
  • It fills the unevenness
  • Non corrosive
  • Immediate results on water or air
  • High chemical resistance; it resists also against engine oil
  • High pressure and UV resistance
  • Temperature range: -60°C to + 300°C
  • Easy to remove
Article nr Name Content
T571701 Seal Flex HT red 200ml 200ml
T571702 Seal Flex HT red 310ml

» To the shop
  • Technical data
  • Application and usage
  • Downloads

Form: pasty
Material: acetoxy RTV silicone
Colour: red
Odour: characteristic
Density (at 20°C): 1,04 g/cm³
Viscosity: non-sag paste
Tack-free time: 10 min
Cure time (at 23°C, 50% r.h.): 4mm/24h
Hardness Shore A: 25
Tensile strength: 1,8 MPa
Shear strength (alu, 1mm): 2,0 MPa
Elastic Modulus (100%): 0,52 MPa

Elongation at break: 500%
Recovery from deformation: 98%
Temperature resistance: -60°C to 300°C
Dielectric strength: 20 kv/mm (ASTM D 419)
Dielectric constant: 3 at 1 Mhz (ASTM D 150)
Dielectric dissipation factor: 3x10-3 at 1 Mhz (ASTM D 150)
Volume resistivity: 2x1015 OHM cm (ASTM D 257)
Thermal conductivity: 315 cal/sec./cm², °C/cm
Shelf life: 24 months in unopened packing below 25°C

  • SEAL FLEX HT RED is developed for many industrial sealing and insulating application, including metal and glass construction, automotive, marine, mechanical engineering, screw thread connections, machine tools, maintenance, connections, air ducts, inlet and outlet manifolds, compressors, pumps, turbines, electrical/electronic, aerospace and consumer products.
  • insulating and moisture-proofing  of engine and electrical boxes
  • sealing of water leakages on rear lights and body joints
  • SEAL FLEX HT RED is jointing to: metals and different alloys, glass, ceramics and several kinds of synthetic materials
  • SEAL FLEX HT RED is resistant to: light acids (up to 20%), glycol, fluor-chlorine-methane, butane, oils, greases, lubricants, petrol, kerosene, transmission and brake fluids, water, steam, antifreeze agents, fuel oil, alkali, saline solutions
  • For an optimal adhesion, the surfaces should be dry and free from corrosion, oil/grease or dust. Therefore we recommend cleaning the surface with a solvent.
  • We recommend to test SEAL FLEX HT on the substrate before use