Region:
TECH-MASTERS GroupChanging region
  • TECH-MASTERS Austria
  • TECH-MASTERS Germany
  • TECH-MASTERS Croatia
  • TECH-MASTERS Czech
  • TECH-MASTERS Poland
  • TECH-MASTERS Slovakia
  • TECH-MASTERS Hungary
  • TECH-MASTERS Romania
  • TECH-MASTERS Slovenia
  • TECH-MASTERS Italia
  • TECH-MASTERS Group

Seal & Lock

SEAL & LOCK is a universal medium strength and
thixotropic anaerobic adhesive and sealant, which
may be used as threadlocker or fastener for stud
bolts, and to bond ball and roller bearings into
housings or tooth wheels on axles. This grade may be used also as pipe und flange sealant and seals most common threaded pipe connectors. SEAL & LOCK cures even at lower temperatures (> 0°C). The practical pressurized can of 100ml allows to apply it easily and very precise in 360° position.
Certified acc. to DVGW (DIN EN 751-1) and to ANSI/NSF Standard 61 for use in commercial and residential potable water systems not exceeding +82° C.

  • Universal anaerobic bonding and sealing
  • Threadlocking, Pipe sealing, Flange sealing and Retaining in one product
  • Perfect dosing even upside down
  • Perfect adjusting time
  • No hazard signs
  • Temperature resistance from -55°C up to +150 °C
  • In practical pressurized can
  • NSF / DVGW Registered
Article nrNameContent
T560001Anaerobic Activator100ml
T567001Seal & Lock100ml

  • Technical data
  • Application and usage
  • Downloads

Physical Properties (liquid product)
Chemical Base: Diester of Methacrylic Acid
Colour: yellow/ fluorescent at 365nm
Viscosity: 25°C Brookfield RVT
55000 – 80000 mPas spindle/ rpm 6/ 2,5
18000 – 30000 mPas 6/ 20
Density: 1.05 g/cm³ 25°C
Max. thread diameter: 3 inches (M 80)
Max. gap filling: 0.50 mm
Flash point: > 100°C
Shelf life: 1 year at room temperature

Physical Properties (cured product)
Initial strength after: 15 - 30 minutes
Functional strength after: 1 - 3 hours
Final strength after: 3 - 6 hours
Loose-break torque: 10 - 20 Nm (M10),
DIN EN 15865
Prevailing torque: 10 - 15 Nm (M10)
Shear strength: 6 – 13 N/mm²  (DIN EN 15337)
Thermal range: - 55°C up to +150°C
 

  • ATTENTION:
    The use of SEAL & LOCK  is not recommended for  threads, cut in copper or copper alloys, which have contact with hot water (>40°C), without any preliminary testing.
    In Germany not allowed for use in household gas-installations acc. to TRGI ´86/96.
  • Threadlocking, Pipe sealing, Flange sealing, Retaining.


  •  

Seal & Lock

SEAL & LOCK is a universal medium strength and
thixotropic anaerobic adhesive and sealant, which
may be used as threadlocker or fastener for stud
bolts, and to bond ball and roller bearings into
housings or tooth wheels on axles. This grade may be used also as pipe und flange sealant and seals most common threaded pipe connectors. SEAL & LOCK cures even at lower temperatures (> 0°C). The practical pressurized can of 100ml allows to apply it easily and very precise in 360° position.
Certified acc. to DVGW (DIN EN 751-1) and to ANSI/NSF Standard 61 for use in commercial and residential potable water systems not exceeding +82° C.

  • Universal anaerobic bonding and sealing
  • Threadlocking, Pipe sealing, Flange sealing and Retaining in one product
  • Perfect dosing even upside down
  • Perfect adjusting time
  • No hazard signs
  • Temperature resistance from -55°C up to +150 °C
  • In practical pressurized can
  • NSF / DVGW Registered
Article nrNameContent
T560001Anaerobic Activator100ml
T567001Seal & Lock100ml

  • Technical data
  • Application and usage
  • Downloads

Physical Properties (liquid product)
Chemical Base: Diester of Methacrylic Acid
Colour: yellow/ fluorescent at 365nm
Viscosity: 25°C Brookfield RVT
55000 – 80000 mPas spindle/ rpm 6/ 2,5
18000 – 30000 mPas 6/ 20
Density: 1.05 g/cm³ 25°C
Max. thread diameter: 3 inches (M 80)
Max. gap filling: 0.50 mm
Flash point: > 100°C
Shelf life: 1 year at room temperature

Physical Properties (cured product)
Initial strength after: 15 - 30 minutes
Functional strength after: 1 - 3 hours
Final strength after: 3 - 6 hours
Loose-break torque: 10 - 20 Nm (M10),
DIN EN 15865
Prevailing torque: 10 - 15 Nm (M10)
Shear strength: 6 – 13 N/mm²  (DIN EN 15337)
Thermal range: - 55°C up to +150°C
 

  • ATTENTION:
    The use of SEAL & LOCK  is not recommended for  threads, cut in copper or copper alloys, which have contact with hot water (>40°C), without any preliminary testing.
    In Germany not allowed for use in household gas-installations acc. to TRGI ´86/96.
  • Threadlocking, Pipe sealing, Flange sealing, Retaining.


  •