Region:
TECH-MASTERS GroupChanging region
  • TECH-MASTERS Austria
  • TECH-MASTERS Germany
  • TECH-MASTERS Croatia
  • TECH-MASTERS Czech
  • TECH-MASTERS Poland
  • TECH-MASTERS Slovakia
  • TECH-MASTERS Hungary
  • TECH-MASTERS Romania
  • TECH-MASTERS Slovenia
  • TECH-MASTERS Italia
  • TECH-MASTERS Group

Seal & Bond MS Construct

Product variant for
General «
General
Automotive

Seal & Bond MS Construct is a high tech adhesive
kit with an extremely quick and very powerful
setting on the widest range of materials. This
solvent and isocyanate-free assembly adhesive
has a very high tensile strength and does not
show signs of ageing. Seal & Bond MS Construct is neutral and acid-free, and can be used on a variety of materials, even natural stone. Seal & Bond MS Construct allows for 40 mm adhesive strips without any deformation.

  • Does not sag.
  • 1-component MS-Polymer.
  • No need for primer anymore.
  • Extreme tensile strength 23 kg/cm².
  • For indoor and outdoor use.
  • Can be applied on humid background.
  • Hardens quickly.
  • Can be painted over.
Article nrNameContent
N531106Seal & Bond MS Construct black cart.290ml
N531107Seal & Bond MS Construct black saus.310ml

  • Technical data
  • Application and usage
  • Downloads

Basis: MS-polymer. Colour: Black. Unit weight: 1.5g/cm??
Viscosity: Paste.
Shore hardness (DIN 53505) after 3 weeks at 23°C/50% relative air humidity: 60 shore A.
Shrinkage (DIN 52451) Tensile strength at break: > 450%
Module at 100% tensile strength 23°C (DIN 53504 S2): lON/mm??
Tensile strength (DIN 53504 S2): 2.3 N/mm??
Skin formation: +/- 5 min.
Hardening speed: 24u - 2.5 mm 48u - 3.5 mm.
Temperature limits: -40°C up to +90°C.

Application temperature: from +5°C up to +40°C.
Chemical strength: good: water, sea water, aliphatic solvents, oils, fats, thinned organic acids and lyes
average: ester, ketone bodies and aromatics
poor: concentrated acids, chloride solvents
perfect: weather resistant
Note: Do bonding test first on PE, PP, silicone, teflon,... based surfaces.
Stability: 12 months.
Security measures: please read the safety sheet.

  • For very quick assembly of the most varied building, automotive and construction materials.
  • Application:
    Always apply on a clean, non-greasy surface, it can even be wet.
    Use temperature +5°C up to +40°C.
    Surface cleaning and degreasing with Multifoam and Safety Clean.
    Apply adhesive on one side by dotting and strokes.
    Press down firmly on adhesive.
  • Support is usually unnecessary thanks to its fast setting (test first).
    Adhesive joints can quickly be removed with Safety Clean.
    Adhesive residue can easliy be removed with Safety Clean.
     

Seal & Bond MS Construct

Product variant for
 «
General
Automotive

SUPER BRAKE CLEANER is efficient and quick. It removes oily dirty and grease from surfaces like metal, glass, ceramic, textiles and most of synthetic material.
SUPER BRAKE CLEANER, unlike traditional solvents, does not leave residues and needs just an application. In case of deep dirty, let SUPER BRAKE CLEANER work for a few minutes, then repeat the application

  • Cleans and degreases in a few seconds.
  • Excellent cleaner for brakes, injectors and fuel systems.
  • Leaves the surfaces dry.
  • Quick and powerful penetration.
Article nrNameContent
N531106Seal & Bond MS Construct black cart.290ml
N531107Seal & Bond MS Construct black saus.310ml

  • Technical data
  • Application and usage
  • Downloads

Colour:  colourless. 
Odor: Characteristic. 
Appearance: Liquid. 
Boiling point: < 35°C.
Flash point:  < 0°C. 

Solubility: not soluble in water. 
Specific weight: N.D. 
Safety measures: consult the Safety Data Sheet.

  • SUPER BRAKE CLEANER is recommended for several uses. For this reason it`s an ideal cleaner for industries, clean-up crews and also garages.
    Effective cleaning on:
    Disk brakes and drums
    Transmission clutch, brake lining and accessories.
    Engine component.
    Injectors.
    Removes the dirty of permanent felt-tipped pens from non porous surfaces.
  • An excellent cleaner ideal to use before applying NOVATIO products ( adhesives, sealants, etc...)

Seal & Bond MS Construct

Product variant for
 «
General
Automotive

Seal & Bond MS Construct is a high tech adhesive
kit with an extremely quick and very powerful
setting on the widest range of materials. This
solvent and isocyanate-free assembly adhesive
has a very high tensile strength and does not
show signs of ageing. Seal & Bond MS Construct is neutral and acid-free, and can be used on a variety of materials, even natural stone. Seal & Bond MS Construct allows for 40 mm adhesive strips without any deformation.

  • Does not sag.
  • 1-component MS-Polymer.
  • No need for primer anymore.
  • Extreme tensile strength 23 kg/cm².
  • For indoor and outdoor use.
  • Can be applied on humid background.
  • Hardens quickly.
  • Can be painted over.
Article nrNameContent
N531106Seal & Bond MS Construct black cart.290ml
N531107Seal & Bond MS Construct black saus.310ml

  • Technical data
  • Application and usage
  • Downloads

Basis: MS-polymer. Colour: Black. Unit weight: 1.5g/cm??
Viscosity: Paste.
Shore hardness (DIN 53505) after 3 weeks at 23°C/50% relative air humidity: 60 shore A.
Shrinkage (DIN 52451) Tensile strength at break: > 450%
Module at 100% tensile strength 23°C (DIN 53504 S2): lON/mm??
Tensile strength (DIN 53504 S2): 2.3 N/mm??
Skin formation: +/- 5 min.
Hardening speed: 24u - 2.5 mm 48u - 3.5 mm.
Temperature limits: -40°C up to +90°C.

Application temperature: from +5°C up to +40°C.
Chemical strength: good: water, sea water, aliphatic solvents, oils, fats, thinned organic acids and lyes
average: ester, ketone bodies and aromatics
poor: concentrated acids, chloride solvents
perfect: weather resistant
Note: Do bonding test first on PE, PP, silicone, teflon,... based surfaces.
Stability: 12 months.
Security measures: please read the safety sheet.

  • For very quick assembly of the most varied building, automotive and construction materials.
  • Application:
    Always apply on a clean, non-greasy surface, it can even be wet.
    Use temperature +5°C up to +40°C.
    Surface cleaning and degreasing with Multifoam and Safety Clean.
    Apply adhesive on one side by dotting and strokes.
    Press down firmly on adhesive.
  • Support is usually unnecessary thanks to its fast setting (test first).
    Adhesive joints can quickly be removed with Safety Clean.
    Adhesive residue can easliy be removed with Safety Clean.