Menu
Region:
TECH-MASTERS GroupChanging region
  • TECH-MASTERS Austria
  • TECH-MASTERS Germany
  • TECH-MASTERS Croatia
  • TECH-MASTERS Czech
  • TECH-MASTERS Poland
  • TECH-MASTERS Slovakia
  • TECH-MASTERS Hungary
  • TECH-MASTERS Romania
  • TECH-MASTERS Slovenia
  • TECH-MASTERS Italia
  • TECH-MASTERS Group
+43 7242 9396 1650
« SURFACE PROTECTION AND TREATMENT

Nanocare Protect

NANOCARE PROTECT prevents the infiltration of dirt
and moisture into porous materials and textiles.
NANOCARE PROTECT protects against frost, slows discolouration due to UV radiation and works against moss and mould formation.
NANOCARE PROTECT improves thermal insulation by 30% and makes woven fabrics more durable.
NANOCARE PROTECT is ready for use, contains no solvents and is not flammable. One litre of NANOCARE PROTECT can treat a surface of between 2 and 10 m², depending on the porosity of the substrate.

  • For all porous materials and textiles
  • Also protects against oil, grease, dirt, pollution…
  • For indoor and outdoor use
  • Colourless, odourless and safe
Article nrNameContent
N486305Nanocare Protect5l
N486309Nanocare Protect1l
N486325Nanocare Protect25l
Y875000Trigger Basic12pcs.
Y875002Standard Bottle 1l1 pc.

  • Technical data
  • Application and usage
  • Downloads

Form: liquid
Odour: weak, characteristic
Melting point/Melting range: < 0°C
Boiling point/Boiling point range: > 100°C
Auto ignition: no
Explosion hazard: none
Vapour pressure at 20°C: approx. 23 hPa.
Density at 20°C: approx. 1.07 g/cm³

Solubility in/Miscibility with water: complete
pH value at 20°C: ± 3 (and only apply on substrate with pH value between 6 and 13: so, after cleaning and before treatment with NANOCARE PROTECT, rinse and dry thoroughly)
Safety measures:
Consult the Safety Data Sheet.

  • Clean, rinse and dry the surface if necessary.
  • Apply NANOCARE PROTECT in an upward motion, from bottom to top, in two successive coats, wet on wet.
  • Allow to dry.
  • Apply with a brush or using a low-pressure pump fitted with a flat spray nozzle. The substrate’s temperature should be at least +5°C. Do not apply when it is raining or frosty.
  •  Make sure the work area is well ventilated and always wear a mask with type A filter during application.
  • Dry in 24 hours, depending on substrate, temperature and amount applied. Maximum protection after 7 days.
  • The equipment used can be directly cleaned with water. Immediately wipe off NANOCARE PROTECT from window panes or frames with a damp cloth.
pdf Product Information
techmasters_en_ptt_PDS.pdftechmasters_en_ptt_PDS.pdf (3.4 MB)

Nanocare Protect

NANOCARE PROTECT prevents the infiltration of dirt
and moisture into porous materials and textiles.
NANOCARE PROTECT protects against frost, slows discolouration due to UV radiation and works against moss and mould formation.
NANOCARE PROTECT improves thermal insulation by 30% and makes woven fabrics more durable.
NANOCARE PROTECT is ready for use, contains no solvents and is not flammable. One litre of NANOCARE PROTECT can treat a surface of between 2 and 10 m², depending on the porosity of the substrate.

  • For all porous materials and textiles
  • Also protects against oil, grease, dirt, pollution…
  • For indoor and outdoor use
  • Colourless, odourless and safe
Article nrNameContent
N486305Nanocare Protect5l
N486309Nanocare Protect1l
N486325Nanocare Protect25l
Y875000Trigger Basic12pcs.
Y875002Standard Bottle 1l1 pc.

  • Technical data
  • Application and usage
  • Downloads

Form: liquid
Odour: weak, characteristic
Melting point/Melting range: < 0°C
Boiling point/Boiling point range: > 100°C
Auto ignition: no
Explosion hazard: none
Vapour pressure at 20°C: approx. 23 hPa.
Density at 20°C: approx. 1.07 g/cm³

Solubility in/Miscibility with water: complete
pH value at 20°C: ± 3 (and only apply on substrate with pH value between 6 and 13: so, after cleaning and before treatment with NANOCARE PROTECT, rinse and dry thoroughly)
Safety measures:
Consult the Safety Data Sheet.

  • Clean, rinse and dry the surface if necessary.
  • Apply NANOCARE PROTECT in an upward motion, from bottom to top, in two successive coats, wet on wet.
  • Allow to dry.
  • Apply with a brush or using a low-pressure pump fitted with a flat spray nozzle. The substrate’s temperature should be at least +5°C. Do not apply when it is raining or frosty.
  •  Make sure the work area is well ventilated and always wear a mask with type A filter during application.
  • Dry in 24 hours, depending on substrate, temperature and amount applied. Maximum protection after 7 days.
  • The equipment used can be directly cleaned with water. Immediately wipe off NANOCARE PROTECT from window panes or frames with a damp cloth.
pdf Product Information
techmasters_en_ptt_PDS.pdftechmasters_en_ptt_PDS.pdf (3.4 MB)